NanoMax PRODUCT CODE: Epoxy_Pool_5

In stock

Two-component epoxy paint, for swimming pools, solvent-based, SurfaPaint Epoxy Enamel, Nanophos 5L

Ideal for concrete and polyester substrates
Excellent resistance to water, chlorinated compounds, alkalis, diluted acids and mineral oils
Excellent adhesion to the substrate
Ideal for large temperature differences
Very good penetration capacity due to its balanced composition
Flawless glossy finish

Regular price: €113,00
Regular price: ~~€130,00~~
Sale price: €113,00

1x PIECE

Add to cart

SAVE 5%

€226,00

SAVE 5%

The most selected

Add to cart

SAVE 12%

€678,00

SAVE 12%

Just to be sure

Add to cart

Practical Advice

For superior protection against chemical agents or abrasion, apply aNanoMax epoxy or polyurethane varnishas a final sealing layer.

100% Surface Protection or Your Money Back!

Free 2 day shipping from €150

TECHNICAL DETAILS:

COVERAGE: 8-10m2/L, 2 coats recommended COVERAGE: 8-10m2/L, 2 coats recommended

Description

SurfaPaint™ Two-Component Epoxy Paint is a two-component, solvent-based epoxy paint.

It is specially designed for the protection of swimming pools, fountains and water tanks . It has excellent resistance to fresh and salt water, chlorination products, acids, alkalis and sunscreen oils.

Thanks to its two-component composition, it creates a strong and at the same time flexible film, which exhibits excellent behavior against surface contraction and expansion, high temperatures and abrasion, and helps maintain a good color condition for longer.

It is self-priming and has strong adhesion to concrete or cement mortar surfaces. It is suitable for new pools or those that have been painted over time.

SurfaPaint™ Pool Epoxy Enamel is an epoxy coating for use on cement substrates such as swimming pools, tanks, fountains, where high impact and/or friction loads are observed.

Application Instructions

Recommended to apply at least 12 hours preventively Epoxy Primer before applying Surfadur to reduce the paint consumption rate and increase adhesion.
MIXING: Pour component B into component A and mix very well for 3 minutes with a drill at low speed. Mixing should be carried out both on the walls and the bottom of the container for proper homogenization.
Then, if necessary, dilute with NanoPhos Thinner A (5-10% v/v) depending on the application, desired workability and substrate absorption.
APPLICATION: Apply by roller, brush or airless spray. SurfaPaint™ Pool Epoxy Enamel dries superficially in 2-3 hours and can be repainted after 12 hours.
The drip time should not exceed 2 days. The pool can be filled with water 7 days after painting, when the paint has completely dried. These times vary depending on the relative humidity and ambient temperature. All tools and equipment should be cleaned immediately after use with NanoPhos Thinner A.
Sunlight and UV radiation will cause bleaching and discoloration over time. Premature bleaching can occur if the water pH is outside the range of 7.0-7.6. Early contact with water can cause premature discoloration, bleaching, and blistering. Superchlorinated water can cause a bleached appearance.

Note this:

Does not apply towet, dusty or surfaces contaminated with oil, grease or de-icing salts.
Not compatible withold oil-based paints, alkyd varnishes or glossy substrates, without prior pickling.
It is not recommended to apply totemperatures below +10°C or above +30°Cor in environments with relative humidity >85%.
Does not apply tofresh concrete(under 28 days) or on surfaces with humidity >4%.The pot life of the mixture is limited (30–40 min)– the product must be applied immediately after mixing.
Not intendedelastic, flexible surfaces or surfaces exposed to strong vibrations.

100% Surface Protection or Your Money Back!

Free 2 day shipping from €150

FREE SHIPPING on all orders over $100

EASY RETURNS 30-day postage paid returns

10% OFF your first order | Use code: FIRST10

HIGH DEGREE OF COVERAGE

One coat is enough to achieve the desired effect. 1ITenough to cover a surface area ofapproximately 10-12 m².

LONG-LASTING PROTECTION

Creates a waterproofing layer with long-lasting resistance

PROTECT WITH NANOTECHNOLOGY

Strong adhesion to "difficult" surfaces.

HOW TO USE

SURFACE PREPARATION - PRIMER

Recommended to apply at least 12 hours preventively Epoxy Primer before applying Surfadur to reduce the paint consumption rate and increase adhesion.

shuffle

MIXING: Pour component B into component A and mix very well for 3 minutes with a drill at low speed. Mixing should be carried out both on the walls and on the bottom of the container for proper homogenization. Then, if necessary, dilute with NanoPhos Thinner A (5-10% v/v) depending on the application, the desired workability and the absorption of the substrate.

APPLICATION

APPLICATION: Apply by roller, brush or airless spray. SurfaPaint™ Pool Epoxy Enamel dries superficially in 2-3 hours and can be repainted after 12 hours. Repainting time should not exceed 2 days. The pool can be filled with water 7 days after painting, when the paint has completely dried. These times vary depending on the relative humidity and ambient temperature. All tools and equipment should be cleaned immediately after use with NanoPhos Thinner A. Sunlight and UV radiation will cause bleaching and discoloration over time. Premature bleaching may occur if the water pH is outside the range of 7.0-7.6. Early contact with water can cause premature discoloration, bleaching and blistering. Superchlorinated water can cause a discolored appearance.

Guarantees

Top Quality Guaranteed

Welcome to our store.
Proven Results & Long-Lasting Protection

Welcome to our store.
Eco-Friendly

Welcome to our store.
We Deliver What We Promise

Welcome to our store.

FAQ

What types of surfaces can the paint be applied to?

NanoMax two-component epoxy paint is ideal forconcrete, metal, mosaic or other rigid surfacesIt is important that the substrate is clean, dry and well prepared (sanded/degreased), and in the case of concrete – completely cured.

Is it resistant to chemicals?

Yes. The epoxy formula providesexcellent resistance to oils, fuels, solvents and other chemical agents, being ideal for workshops, parking lots or industrial halls.

What is the working time after mixing the two components?

After mixing components A and B, the paint has apot life of approximately 30–40 minutes, depending on the temperature. It is essential to apply it within this range to avoid hardening in the container.

Can it be used to obtain a non-slip floor?

Yes. For an anti-slip effect, it can be sprinkledquartz sand between layers, followed by a sealing layer. This system is useful in industrial spaces, parking lots or areas with a risk of slipping.